MIL-DTL-24211/1D
E ± .01
G ± .01
Part number
A
B
C
D
M24211/1-
(.25)
(.25)
1.122 ± .004
.497 ± .004
.561 ± .002
.2485 ± .0020
001
1.532
.907
(28.50 ± .10)
(12.62 ± .10)
(14.25 ± .05)
(6.31 ± .05)
(38.91)
(23.04)
.900 ± .003
.400 ± .003
.4500 ± .0015
.2000 ± .0015
002
1.300
.800
(22.86 ± .08)
(10.16 ± .08)
(11.43 ± .04)
(5.08 ± .04)
(33.02)
(20.32)
.622 ± .002
.311 ± .002
.311 ± .001
.1555 ± .0010
003
1.006
.695
(15.80 ± .05)
(7.90 ± .05)
(7.90 ± .03)
(3.95 ± .03)
(25.55)
(17.65)
.340 ± .002
.170 ± .002
.170 ± .001
.085 ± .001
004
.580
.410
(8.64 ± .05)
(4.32 ± .05)
(4.32 ± .03)
(2.16 ±.03)
(14.73)
(10.41)
.420 ± .002
.170 ± .002
.210 ±.001
.085 ± .001
005
.660
.410
(10.67 ± .05)
(4.32 ± .05)
(5.33 ± .03)
(2.16 ± .03)
(16.76)
(10.41)
.2800 ± .0015
.1400 ± .0015
.1400 ± .0008
.0700 ± .0008
006
.474
.334
(7.11 ± .04)
(3.56 ± .04)
(3.56 ± .02)
(1.78 ± .02)
(12.04)
(8.48)
L ± .01
M ± .02
S ± .003
U ± .02
V ±. .005
W ± .005
Part number
K
N
X
M24211/1-
Min
(.25)
(.51)
(.08)
(.51)
(.13)
(.13)
.676 ± .002
.737 ± .002
001
.94
1.88
.169
1.25
.026
.110
.064
(17.17 ± .05)
(18.72 ± .05)
(23.88)
(47.75)
(4.29)
(31.75)
(.66)
(2.79)
(1.63)
.610 ± .002
.640 ± .002
002
.82
1.63
.169
1.06
.026
.110
.050
(15.49 ± .05)
(16.26 ± .05)
(20.83)
(41.40)
(4.29)
(26.92)
(.66)
(2.79)
(1.27)
.497 ± .002
.478 ± .002
003
.66
1.31
.144
.88
.026
.110
.040
(12.62 ± .05)
(12.14 ± .05)
(16.76)
(33.27)
(3.66)
(22.35)
(.66)
(2.79)
(1.02)
.320 ± .001
.335 ± .001
004
.44
.88
.116
.57
.020
.100
.040
(8.13 ± .03)
(8.51 ± .03)
(11.18)
(22.35)
(2.95)
(14.48)
(.51)
(2.54)
(1.02)
.320 ± .001
.335 ± .001
005
.44
.88
.116
.57
.020
.100
.040
(8.13 ± .03)
(8.51 ± .03)
(11.18)
(22.35)
(2.95)
(14.48)
(.51)
(2.54)
(1.02)
.250 ± .001
.265 ± .001
006
.38
.75
.116
.47
.015
.080
.040
(6.35 ± .03)
(6.73 ± .03)
(9.65)
(19.05)
(2.95)
(11.94)
(.38)
(2.03)
(1.02)
NOTES:
1. Dimensions are in inches.
2. Millimeters are in parentheses.
3. Metric equivalents (to the nearest 0.01 mm) are given for general information only and are based
upon 1 inch = 25.4 mm.
4. Except where noted, break sharp edges and remove burrs.
5. Flange is symmetrical about both centerlines.
6. Electrical contact area to be at least 0.003 (0.08) higher than adjacent metal surface.
7. Surface roughness of mating surfaces other than the raised electrical contact area shall be no
greater than 63 micro inches in accordance with ASME-B46.1.
8. Any raised embossed pattern for electrical contact is acceptable provided R.F. leakage
requirement is met.
FIGURE 1. Dimensions and configuration. Continued
3
For Parts Inquires submit RFQ to Parts Hangar, Inc.
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business